My use for the DFT
In ECE 301 students were introduced to the concept of Fourier Transforms. No matter whom you had been taught by it seemed intimidating and confusing. And irrelevant. They tried to show you where and how it was used but honestly how long did it take for you to finally realize its use? For me two semesters! There were CTFTs, DTFTs and DFTs (and I am sure there are more that I have not been introduced to yet) and they were all a blur of equations that sometimes gave me nightmares. I am not a very mathematical person: I like engineering concepts and ideas but dislike the math behind it because the equations often stop making sense after the fifth Greek letter has been added. So the goal should be to make such math (these transforms rather) and relate them to real life, not just by telling us where it used but by telling us how it is. So I am going to attempt to do that with my limited knowledge of the math that goes one behind the screen.
What is a Fourier Transform?
A Fourier Transform (FT for short) is just an equation that allows us to from the time domain to the frequency domain and the inverse FT performs the reverse. The time domain is just the real time representation of our signal; how the signal varies over time whereas the frequency domain shows us the number of times the main component of a signal repeats per second.
In the time domain you look at the value of something as it changes over time - a series of snapshots, if you will. In the Fourier domain you look at the entire lifetime of the signal all at once - and analyze it in terms of the underlying frequencies that made it up. This means you can no longer see the value at any one time, or the rate at which the signal is changing at any one time. Instead, for each possible frequency, you see the amplitude of the signal at that frequency (such a distribution is called a frequency spectrum).
It is thus a technique that can be used to describe almost anything in the world be it an electric signal or the stock market. Did you know that our brain picks up different frequencies around us and performs a Fourier analysis (really quickly and effectively) on data: for example on different voices, or recognizes differences in high and low notes or just perceives different colors? Scientists haven’t yet found out how all that is done but they know for sure that something of that sort goes on in our highly complex brains.
CTFTs, DTFTs and DFTs
CTFT
$ \mathcal{X}(f) = \int_{-\infty}^{\infty} x(t) e^{-j 2 \pi f t} dt $
A CTFT( continuous time fourier transform) is continuous in both the time and frequency domain. Give example here.
DTFT
$ X(\omega) = \sum_{n=-\infty}^{\infty} x[n] \,e^{-i \omega n}. $
A DTFT (discrete time fourier transform) is performed on signals which are discrete in the time domain but are continuous in the frequency domain.the DTFT requires an input function that is discrete. Such inputs are often created by sampling a continuous function, like a person's voice where the air expelled from the lungs is continuous (signal) and then the vocal tracts take samples of it, periodically to produce a discrete signal. Often the $ x[n]\, $ sequence represents the values (aka samples) of a continuous-time function, $ x(t)\, $, at discrete moments in time: $ t = nT\, $, where $ T\, $ is the sampling interval (in seconds), and $ 1/T = f_s\, $ is the sampling rate (samples per second). Then the DTFT provides an approximation of the continuous time Fourier transform.
Since $ f\, $ represents ordinary frequency (cycles per second) and $ f_s\, $ has units of samples per second, the units of $ f / f_s\, $ are cycles per sample. It is common to replace this ratio with a single variable, called normalized frequency, which represents actual frequencies as multiples (usually fractional) of the sample rate. ω is also a normalized frequency, but its units are radians per sample. The normalized frequency has the added bonus that the function X(ω) is periodic with period 2π.
DFT
- $ X_k = \sum_{n=0}^{N-1} x_n e^{-\frac{2 \pi i}{N} k n} \quad \quad k = 0, \dots, N-1 $
The sequence of N complex numbers x0, ..., xN−1 is transformed into the sequence of N complex numbers X0, ..., XN−1 by the DFT according to the above formula where i is the imaginary unit and is a primitive N'th root of unity. A DFT (discrete fourier transform) is performed on discrete time signals too but they are also discrete in the frequency domain.
A DFT is almost the same as a DTFT because if the DTFT of a signal is truncated to make it finite length then the resulting waveform will be the same as the result of a DFT being performed on the signal ( this is of course easier said than done because we then have to use a filter of the appropriate length and so on, which means another two pages of math).
Either way you still have to know the formulas for the sums of a geometric series, infinite or not.
For $ r\neq 1 $, the sum of the first n+1 terms of a geometric series is:
- $ a + ar + a r^2 + a r^3 + \cdots + a r^{n} = \sum_{k=0}^{n} ar^k= a \, \frac{1-r^{n+1}}{1-r}, $
where a is the first term of the series, and r is the common ratio. The formula follows by multiplying through by a.
As n goes to infinity, the absolute value of r must be less than one for the series to converge.
Project Rhea
So Professor Mimi and I decided to apply my new found knowledge on this website. As this is a student oriented website (and so far it's usage is only restricted for classes e.t.c) it is still not as well known or well used as it should be. It works but it is a work in progress and the Rhea development team wants it to be go-to website for the School of ECE here at Purdue. Therefore we needed to see trends in visits and reasons behind those trends. Only after we get an idea of why and who visited Rhea could we implement further changes that would benefit the website.
This is how we found those trends:
• A Google Analytics account was set up for the website which monitored the number of visits per day and also recorded many, many other details about each visit.
• The number of visits per day from the beginning of fall 2009 to present day was downloaded and the discrete time signal was plotted. Let’s call this signal x[n].If you notice the plot is continuous: this is because there are simply too many points to plot discretely so to prevent getting messy we use the plot command in Matlab instead of stem.
 |
 |
|---|
This original x[n] however had too many oscillations for us to get any useful information out of it: we couldn’t tell whether the general traffic increased or decreased over two semesters or remained constant, or what the weekly/monthly variations were.
• Therefore a DFT was taken of the x[n] (because the data was discrete and finite in length) and we found that the signal oscillated periodically.
• A low pass filter was then designed with cut off frequencies that represented those weekly variations so that they could be removed.
